Profile Roll Bending Selection Hub

Choosing the right profile bending machine starts with the workpiece, not the brochure. Send a drawing of the angle, channel, beam or box section you need to curve, and this hub walks you through the four choices that decide whether a profile bender will hold your radius — roll layout, drive arrangement, power system and control platform — before you ask for a quote.

3 Roll Vertical Profile Bending Machine
Vertical & horizontal Two machine types, chosen by how the section has to sit in the rolls
3 working rollers Pre-bending, coiling and rounding completed in one feeding pass
NC or CNC Asynchronous motor drive or servo motor drive, both hydraulic
Custom molds Tooling built to customer requirements for your sections
Step 2

Configuration decision matrix

Four choices separate one machine from another. Each row below shows the options the machine is built with and the drawing detail that settles it.

Configuration
Option A
Option B
What to confirm

Roll axis layout

Vertical layout

Rolls stand vertically, the profile is clamped and driven through the rolls. Described on the product page as suited to thick-wall profiles where a horizontal machine cannot maintain straight edges.

Horizontal layout

The alternative machine type offered for profiles that sit better on a horizontal roll set. Confirm against your drawing rather than assuming one layout covers every section.

State the leg length you must keep straight and the heaviest wall thickness in the batch — this is the detail the layout decision turns on.

Roller drive arrangement

Two side rollers as main drive

Side rollers carry the drive while the third roller applies pressure. A common setup for lighter sections and shorter runs.

Three working rollers as main drive

All three working rollers are driven, so the profile is pulled through on every contact point rather than on two.

Confirm how much roller contact your section gives you and how many bends you expect per shift; the answer decides which drive arrangement is worth paying for.

Power system

NC — asynchronous motor

A straightforward hydraulic power system with numerical control of the bend sequence.

CNC — servo motor

Servo-synchronised roller adjustment with real-time torque balancing and stored bend programs that can be recalled for repeat work.

Confirm how many different radii appear in a typical batch and whether the same radius returns month after month.

Control platform

PLC control

PLC-based control for the machine sequence, with a touchscreen CNC panel for setup and operation.

Industrial computer

Industrial-computer control for plants that want stored programs, MES integration and remote diagnostics as part of the machine specification.

Confirm whether the shop floor already runs an MES or a production-record system that the machine should report into.




3 Roll Vertical Profile Bending Machine
Vertical roll layout with three active rollers — model numbers CAT-VPBNC-M12T and CAT-VPBCNC-M20T.
Machine reference

Specification at a glance

These are the published parameters for the 3 Roll Vertical Profile Bending Machine. Anything not listed — tonnage, motor power, overall dimensions, maximum radius — should be confirmed in writing against your drawing rather than assumed.

Control system PLC control or industrial computer
Number of active rollers 3
Machinable materials Angle steel, channel steel, flat steel, round steel, round pipe, square pipe, I-beam and similar profiles; wide-flange beams, box sections and heavy structural profiles are also described on the product page
Model numbers CAT-VPBNC-M12T, CAT-VPBCNC-M20T
Accuracy / repeatability ±0.1 mm on profile radius
Power system options NC (asynchronous motor) or CNC (servo motor)
Roller drive configuration Two side rollers as main driving rollers, or three working rollers as main driving rollers
Step 3

Match the job to the configuration

Four situations come up again and again in fabrication shops. Each one points to a specific machine feature — and to a question worth asking before you sign.

One radius, run after run

The same beam radius repeats across every production batch, and setup time is eating the margin.

CNC servo control stores and recalls bend patterns. Ask how many programs can be held and whether the panel can report run data to your MES.

Thick wall, straight leg

The profile is heavy, and the unbent legs have to stay true or the part will not fit at assembly.

The vertical roll layout is described as reducing profile distortion where a horizontal machine cannot maintain straight edges. Confirm your leg straightness tolerance on the drawing.

A mixed book of sections

Angle one week, channel and box section the next — the machine has to change over without a tooling project each time.

Molds are customisable to customer requirements. List every section and thickness in the enquiry so the tooling set is quoted as one package.

Springback keeps spoiling the radius

The first parts come off under-bent, and the operator spends the shift chasing the radius by hand.

Servo-synchronised roller adjustment and real-time torque balancing are part of the machine design, alongside ±0.1 mm repeatability. Ask for a trial bend on your material grade before accepting the tolerance.
Step 4

What the drawing review needs from you

A quote built on a section name alone is a guess. These six details let the roll layout, the control platform and the mold set be matched to the part you actually have to ship.

  1. 1 Wall thickness Every thickness on the section, not just the heaviest one.
  2. 2 Material and yield strength Grade and yield point, because springback behaviour changes with the material.
  3. 3 Target radius State whether it is an inner, centreline or outside radius, and mark the tightest radius on the part.
  4. 4 Leg length and section size The full section geometry with leg lengths and flange widths, not only the shape name.
  5. 5 Quantity and batch pattern One-off, prototype or repeating batch — and how many distinct radii each program has to cover.
  6. 6 Tolerance and straightness The radius tolerance you inspect to, plus the allowed deviation on the unbent legs.

What happens after you send it

  1. Feasibility review Your section is checked against the roll layout, drive arrangement and control options that fit it.
  2. Tooling and control proposal The mold set is specified for your sections, and the power system and control platform are fixed for your batch pattern.
  3. Delivery and technical support Quotation, build timing and technical support are confirmed in writing before the order is placed.

Send a drawing, get a matched configuration

Share the section, wall thickness, target radius and quantity. The reply is an engineering review of your part against a 3-roll vertical configuration — roll layout, drive arrangement, NC or CNC power system, control platform and custom molds — not just a price line.

Custom tooling is built to customer requirements, so the mold set is quoted together with the machine.

Related Reading

Three notes to help clarify product requirements before contacting the supplier.

CNC 3 Roll Bender Setup for Heavy Machinery Batch Production

Batch bending in a heavy machinery plant is decided by changeover work, not by the best single part the machine can produce.

Read article

What Does a Vertical 3-Roll Profile Bender Do in Heavy Steelwork?

Walk into a heavy fabrication shop and you will usually see a plate roll, a press brake, and something in the corner that looks like three wheels standing upright on a welded frame.

Read article

Why Does a Vertical Roller Layout Reduce Sag in Heavy Steel Profiles?

In heavy steel profile bending, the workpiece is often far longer than the machine’s roll area.

Read article

Frequently Asked Questions

which profiles can the machine bend?

the product page lists angle steel, channel steel, flat steel, round steel, round pipe, square pipe and I-beam, and states that wide-flange beams, box sections and heavy structural profiles are also described.

how many active rollers does it use?

three. the roller drive configuration can be either two side rollers as the main driving rollers or three working rollers as the main drive, which changes how much the profile slips during a pass.

what accuracy is quoted?

plus or minus 0.1 mm on profile radius. that figure is a machine capability, so the drawing tolerance you accept should be set against it rather than against a general bending tolerance.

what is the difference between the two models?

CAT-VPBNC-M12T and CAT-VPBCNC-M20T differ in power system options: NC with an asynchronous motor, or CNC with a servo motor. the NC path suits repeat jobs, the CNC path suits varying radii and profiles.

what control system is fitted?

either a PLC control or an industrial computer. both are listed as options, so the control choice belongs in the enquiry alongside the profile drawing.

what should be sent with a bending enquiry?

a drawing of the section to be curved, the material, the finished radius, the quantity and the tolerance you can accept. the page frames the whole decision around the workpiece rather than the brochure.